Upper chassis plate
Lower chassis
Aluminum chassis post/ bellcrank post set w/spacers (Use with graphite chassis)
Shock shafts, hardened steel, titanium nitride coated (29mm) (front) (2)
Shock shafts, hardened steel, titanium nitride coated (32mm) (2)
Upper chassis deck, composite
Upper chassis deck (grey), composite
ADJ. PLATE, SCREWS, WASHERS
Hard carbide diff balls (1/8)(10)
Chassis plate, T6 aluminum
Chassis, lower main
Flywheel, (larger, knurled for use with starter boxes) (TRX 2.5 and TRX 2.5R) (silver anodized)
Gearbox halves (front & rear)/ shift detent ball/ spring/ 4mm GS/ shift shaft seal, glued/ 2.5x8mm CS (2)
Gearbox halves (f&r)/ screws (3x12 RST)(5)/40mm guide pin/ idler gear shafts (2)/idler gear shaft support (1)
Input shaft/ drive gear assembly (18-tooth steel top gear)
Sport Wheels, Maxx (mirror chrome finish) (2)
Main chassis (black)
Plate, motor (for single motor installation, use gear cover #3977X)
Plate, motor
Chassis backbone, plastic/ throttle servo mount (grey)
Chassis backbone, plastic/ throttle servo mount
R. SHOCK TWR (N. STAMPEDE)
Backplate (for recoil start engines)
Thrust bearing/thrust washers (2)/belleville spring washers (2)
Upper chassis (grey)
Bumpers, front and rear (black chrome)
Servo horns, steering and throttle (for non-Traxxas servos (Hitec, JR, KO, Airtronics))
Box, receiver & battery (2)/ cover/ foam pad & adhesive/ charge jack plug (rubber)/ 4x8mm BCS (1)/ 4x12mm BCS (2) (contains both boxes to accommodate either AA battery holder or RX flat pack)
Backplate/ 20x1.4mm O-ring (for engines w/o starter) (TRX 2.5, 2.5R, 3.3)
Wheels, SS (split spoke) 3.8" (satin) (2) (fits Revo/Maxx series) 5172 - revo 3.3, t->
Wheel nuts, splined, 17mm (blue-anodized) (4)
Wheel nuts, splined, 17mm (green-anodized) (4)
Gearbox halves (front & rear)/ rubber access plug/ shift detent ball/ spring/ 4mm GS/ shift shaft seal, glued
Chassis brace, Revo/Slayer (3mm 6061-T6 aluminum) (titanium- anodized)/ 4x16mm BCS
Chassis brace, Revo (3mm 6061-T6 aluminum) (blue-anodized)/ 4x16mm BCS
Wheels, SS (split spoke) 3.8" (chrome) (2) (use with 17mm splined wheel hubs & nuts, part #5353X) (fits Revo/Maxx series) 5172R - revo 3.3, e-maxx vxl.
Wheels, T-Maxx (chrome) (2)
Wheelie bar arm (1)/ connector (1)/ 3x12 SS (hex drive) (4)
Gearbox halves (f&r)/ rubber access plug
Upper chassis
Rebuild kit (for steel constant velocity driveshafts) (includes pins, dustboots, gaskets, e-clips, x-rings, lube, and hardware for 2 driveshaft assemblies)
Drive cups (2) (attaches to 5mm trans output shaft)/screw pins, M4/15 (2) (for T-Maxx steel constant-velocity center driveshafts)
Ball bearings, blue rubber sealed (20x27x4mm) (2)
Turnbuckles, toe links (5.0mm steel) (front) (2)
Turnbuckles, toe links (5.0mm steel) (rear) (2)
Driveshaft, steel constant-velocity, Revo/Maxx (shaft only, 128.5mm)/ drive cup pin (1)